Models KL-37W1U KL-50W1U KL-50W2U LE-1 chassis
To enter the service mode:
- Turn the mains power on while holding the
"PROG +" and the "PROG -" buttons on the set simultaneously.
- "TT" will appear at the top right
hand corner of the screen
- Press "01" on the remote control to
see the service menu on screen
- Press the "arrow up" and the
"arrow down" buttons on the remote control to navigate the menus
- Press the "OK" button to select an
adjustment
- Press the "arrow up" and the
"arrow down" buttons to highlight an adjustment, and press the "OK"
button to allow adjustment.
- Use the "arrow up" and the
"arrow down" buttons to adjust the value
- Press the "OK" button to store
- Turn off the power to exit the service mode
Test mode 2 allows entry of TT numbers to
perform some functions. The important numbers for this chassis are given below |
| |
| TT00 |
|
switch the TT mode off |
| TT08 |
|
set the set to shipping condition |
| TT15 |
|
Factory reset values |
| TT16 |
|
User defined reset values |
| TT16 loads
the contents of the NVM when the set was last switched off TT15 loads the factory defaults. To do this
press TT15 followed by TT16. |
| Models
: KV25F1U - KV29F1U -
KV25F2U - KV29F2U - KV25F3U - KV29F3U - KV25X1U - KV29X1U - KV24WX1U - KV28WX1U - KV24WS2U
- KN28WS2U - KV28WF1U - KV32WF1U - KV29FX11U - BE-3D chassis KV28DS20U
KV28DX20U KV32DS20U KV32DX20U BE-3E chassis
To access the service mode:
- Turn the set on and then put into standby
- Press the On Screen Display button
- Press the "5" button
- Press the "VOLUME +" button
- Press the "TV" button
- Press the "MENU" button on the
remote control to bring up the test screen
- Use the joystick on the remote control to
navigate the service menu (< > ^ v keys BE-3E)
- Press the right joystick to enter the selected
adjustment
- Turn off the power to store and exit the
service mode
Test mode 2 allows entry of TT numbers to
perform some functions. The important numbers for this chassis are given below |
| |
| TT00 |
|
switch the TT mode off |
| TT08 |
|
set the set to shipping condition |
| TT24 |
|
Set CTV to UK model (PAL I) |
| TT44 |
|
Set all favourite pages to 100 |
To re-initialise the NV Ram follow the
procedure below:
- Set the TV to channel 59
- Select TT49
- Switch off at the mains supply, wait for one
minute and switch the set back on
- Select channel 59, and enter the service mode
- Select TT24, (UK destination)
- Select TT42, (general reset)
- Switch off at the mains, wait for one minute
and switch on again
- Auto tune the channels and carry out a
complete adjustment on the set
|
Models
KP-41S3U RE-1
chassis
To access the service mode:
- Turn the set on and then put into standby
- Press the On Screen Display button
- Press the "5" button
- Press the "VOLUME +" button
- Press the "TV" button
- Use buttons "1" and "4" on
the remote control to navigate the service menu
- Use buttons "3" and "6" to
adjust the selected data
- Press the "MUTE" button and then the
"0" button to store the data
- Press the "5" button and then the
"0" button to initialise the set. (Note, this is an extreme measure and should
be used with caution!)
- Turn the set off to exit
|
Models
KP-41S3U RE-1
chassis
To access the service mode:
- Turn the set on and then put into standby
- Press the On Screen Display button
- Press the "5" button
- Press the "VOLUME +" button
- Press the "TV" button
- Use buttons "1" and "4" on
the remote control to navigate the service menu
- Use buttons "3" and "6" to
adjust the selected data
- Press the "MUTE" button and then the
"0" button to store the data
- Press the "5" button and then the
"0" button to initialise the set. (Note, this is an extreme measure and should
be used with caution!)
- Turn the set off to exit
|
Models KP-41DS1U RE-2D chassis
To access the service mode:
- Turn the set on and then put into standby
- Press the On Screen Display button
- Press the "5" button
- Press the "VOLUME +" button
- Press the "TV" button
- Use the JOYSTICK Up / Down on the remote
control to navigate the service menu
- Move the JOYSTICK to the right > to enter
the selected adjustment
- Press OK on the JOYSTICK to EXIT
- Press the "MUTE" button and then the
"0" button to write data
- Press the "On Screen Display" button
to copy data
- Turn the set off to quit the service mode when
adjustments are complete
|
Models KV-14V4U TE-1 chassis
To access the service mode:
- Turn the set on and then put into standby
- Press the On Screen Display button
- Press the "5" button
- Press the "VOLUME +" button
- Press the "TV" button
- Use buttons "1" and "4" on
the remote control to navigate the service menu
- Use buttons "3" and "6" to
adjust the selected data
- Turn off the power to store and exit the
service mode
The codes on screen are as follows: |
|
|
| ODL |
|
Power On Delay |
|
|
| OSH |
|
On screen H-position |
|
|
| MUT |
|
FTZ muting on |
|
*Do not adjust |
| VAM |
|
V. size
|
|
|
| VBC |
|
V breath correct |
|
*Do not adjust |
| PAM |
|
Parabola amp. |
|
*Do not adjust |
| PTI |
|
Parabola tilt |
|
*Do not adjust |
| VLI |
|
V-linearity |
|
|
| CCR |
|
Corner correction |
|
*Do not adjust |
| HAM |
|
V. cent
|
|
*Do not adjust |
| BIN |
|
Blue intensity |
|
|
| GIN |
|
Green intensity |
|
|
| RIN |
|
Red intensity |
|
|
| CLS |
|
Colour system |
|
|
| SCO |
|
Sub contrast |
|
|
| SBR |
|
Sub brightness |
|
|
| SSA |
|
Sub saturation |
|
|
| SHU |
|
Sub hue |
|
|
| SSH |
|
Sub sharpness |
|
|
| G2 adj |
|
G2 adjustment |
|
|
| 32K adj
|
|
|
|
|
|
|
Models KV-16WS1U KV-21X1U KV-21X4U KV-20WS1U BE-5 chassis
To access the service mode:
- Turn the set on and then put into standby
- Press the On Screen Display button
- Press the "5" button
- Press the "VOLUME +" button
- Press the "TV" button
- Press the "MENU" button on the
remote control to see the service menu on screen
- Use the "blue" button and the
"green" button on the remote control to navigate the service menu
- Use the "Yellow" button and the
"red" button to adjust the selected data
- Turn the set off to exit and store
Test mode 2 allows entry of TT numbers to
perform some functions. The important numbers for this chassis are given below |
| |
| TT00 |
|
switch the TT mode off |
| TT08 |
|
set the set to shipping condition |
| TT26 |
|
Set CTV to UK model (PAL I) |
| TT41 |
|
Re-initialise NVM |
| TT43 |
|
Re-initialise geometry settings |
| Note:
For TT numbers above 41, the channel number needs to be 59 |
Models. KV-32WS4U KV32WX4U KV32WX2U AE-4 chassis
To enter the service mode:
- Turn the mains power on while holding the
"PROG +" and the "PROG -" buttons on the set simultaneously.
- "TT" will appear on the top right
hand corner of the screen.
- Press "MENU" on the remote control
to get the service menu on screen
- Navigate the menu by moving the joystick up
and down.(green and blue)
- Press the joystick down to select an
adjustment.
- Turn TV off to exit service mode
Test mode 2 allows entry of TT numbers to
perform some functions. The important numbers for this chassis are given below |
| |
| TT00,10,20,30,40 |
|
pressing these numbers will
switch the TT mode off |
| TT01 |
|
switch service menu on |
| TT08 |
|
set the set to shipping condition |
| TT21 |
|
picture rotation automatic
function |
| TT25 |
|
Status menu display |
| TT49 |
|
New initialisation |
| |
Models. KV28FD1E KV28FD1K KV32FD1E KV32FD1K GE-1 chassis
To enter the service mode:
- Turn the mains power on while holding the
"PROG +" and the "PROG -" buttons on the set simultaneously.
- "TT" will appear on the top right
hand corner of the screen.
- Press "MENU" on the remote control
to get the service menu on screen
- Navigate the menu by moving the joystick up
and down.(green and blue)
- Press the joystick down to select an
adjustment.
- Turn TV off to exit service mode
The main adjustments are: |
| |
|
|
|
MCP CXA2101 - picture (colour,
drives, brightness etc) |
|
|
|
Deflection control SDA9361 -
geometry |
| |
Models KV-29X5U FE-1 chassis
To access the service mode:
- Turn the set on and then put into standby
- Press the On Screen Display button
- Press the "5" button
- Press the "VOLUME +" button
- Press the "TV" button
- Use buttons "^"(Green) and
"v"(Blue) on the remote control to navigate the service menu
- Press YELLOW button to enter required menu
- Use buttons "<" and
">" to adjust the selected data
- Press the "MENU" button to store the
data and exit
Test Menu |
| Picture |
- |
(RGB. Drives & Cut offs, Sub
Colour, Sub brightness) |
| Geometry |
- |
(Vert. and Horiz. adjustments) |
| Sound |
- |
(NICAM Information) |
| TV Status |
- |
(Destination and Country info.) |
| AGC. Adjust |
|
|
| Technical |
|
|
| |
|
